NSF Product and Service Listings

[1] Mix ratio of Part A:Part B is 1:1

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for use in 45 mm pipe and greater.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum SA/V of 0.25 sq. in./L in pipes and tanks.

[1] Certified for a maximum SA/V of 0.25 sq. in./L in pipes and tanks.

[1] Certified for a maximum SA/V of 0.25 sq. in./L in pipes and tanks.

[1] Certified for a maximum use level of 40 oz/100 lbs cement.

[1] Certified for a maximum surface area to volume ratio of 14.5 square inches/L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum surface area to volume ratio of 14.5 sq. in./L.
[2] Certified for a maximum surface area to volume ratio of 0.4 sq. in./L.

[1] Certified for a maximum surface-to-area ratio of 14.5 sq. in./L.

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L.
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Mix ratio of Part A:Part B is 1 : 1
[2] The exposed surface area of sealant in a tank shall not exceed 1.3 sq. cm/L or 0.2 sq.
    in./L

[1] Certified for use with pipes >=1/4".

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[2] Certified for a maximum use of 2 joints/liter.
[4] Product requires cure of 72 hours at ambient temperature.  Formerly Loctite PST 561 Pipe
    Sealant.
[5] This product is Certified for use as a fitting and pipe sealant.
[6] Maximum use: 50 (1/2") joints per residence (4.5 joints per liter).

[1] Certified for a maximum SA/V of 025 sq. in./L in pipes and tanks.

[1] The exposed surface area of each sealant in a household distribution system should not
    exceed 1.3 sq. cm./L or 0.2 sq. in./L.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Mix ratio of Part A:Part B is 1:1

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Certified for a maximum SA/V of 0.25 Sq. in. /L in pipes and tanks.

[1] Mix ratio of Part A:Part B is 1:1
[2] The exposed surface area of sealant in a tank shall not exceed 0.60 sq. cm/L or 0.095
    sq. in./L
[3] The exposed surface area of sealant in pipes and fittings shall not exceed 1.3 sq. cm/L
    or 0.2 sq. in./L

[1] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] Size corresponds to requested usage of a minimum tank size of 100,000 gallons with a
    maximum surface area of sealant of 2.85%.
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.

[1] Mix ratio of Part A:Part B is 1:1
[2] The exposed surface area of sealant in pipes and fittings shall not exceed 1.3 sq. cm/L
    or 0.2 sq. in./L
[3] The exposed surface area of sealant in a tank shall not exceed 1.3 sq. cm/L or 0.2 sq.
    in./L

[1] Product Certification does not include use of a primer.
[2] Certified for a maximum of 54 1/2" joints per residence (5 joints per Liter).
[3] Product is Certified using the following cure parameters:
    1. I-TPS is to be applied to the male threads only in order to avoid product to protrude
    in back of the assembly.
    2. I-TPS should be allowed to cure at 70 - 80 F for at least 24 hr.
    3. I-TPS not between the threads and exposed to air will not cure. The excess I-TPS must
    be washed or removed after application.

[1] Certified for the following parameters:
    Cure: 7 days at 25 °C
    Mix ratio: 100:3 (A:B) by volume
    Color: Grey
[2] Only the Pouring Grad (PG) is certified.Certification does not include any primers.
[3] Certified for a maximum surface area to volume ratio of 0.7 sq. in./L.
[4] Certified for the following parameters:
    Cure: 7 days at 25 °C
    Color: Black
[5] Certification does not include any primers.
[6] Certified for a maximum surface area to volume ratio of 2.8 sq. in./L.

[1] Product requires cure of 7 days at 23°C and 50% relative humidity.
[2] Certified for a maximum use level of 0.2 square inches per liter.
[3] Product requires cure of 7 days at 23°C.

[1] Certified for a maximum use level of 0.2 square inches per liter.
[2] Certified colors are white, grey, and black.
[3] Product requires cure of 7 days at 23°C and 50% relative humidity.

[1] Certified for a maximum exposed surface area of 216 sq. in./1000 gal.
[2] Certified for a maximum surface area of 568 square inches per 1000 gallons.  Mix ratio
    2:1 (Resin:Cure).

[1] Final Cure Time And Temperature: 14 days at 75ºF
    Special Comments: Mix ratio of Part A:Part B is 100:7 by weight. Induction time of
    15 minutes is required. Certification does not include any primers
[2] Only products bearing the NSF Mark on the product, product packaging, and/or
    documentation shipped with the product are Certified.
[3] Restricted to a maximum surface area to volume ratio of 1% of a 30,000 gallon tank.

[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.

[1] The exposed surface area of each sealant in a household distribution system shall not
    exceed 1.3 sq. cm/L or .2 sq. in./L
[G] Product is Certified to NSF/ANSI/CAN 372 and conforms with the lead content requirements
    for "lead free" plumbing as defined by California, Vermont, Maryland, and Louisiana
    state laws and the U.S. Safe Drinking Water Act.