NSF Product and Service Listings

[2] Description: `R series` range of inline and 90° normally closed, normally open, normally
    closed and latching solenoid valves with plastic bodies and silicone diaphragms. The
    valves are available with various inlet and multiple outlet connections. All models
    excluding “MINI” are available with various accessories including filters, flow
    regulators, flow restrictors or check valve cartridges  on the inlet or outlet, and the
    “MINI” models are available with check valve cartridges or flow regulators in the
    outlet. However, the complete products have not been fully tested to demonstrate they
    provide backflow protection.
    
    Models are available with the RF flow meter module option with the following flowrates:
    3.6 l/min, 7 l/min, 15 l/min or 30 l/min Note: NSF has not verified the accuracy of the
    flow meter modules.
    
    Models are available with the RV Filter option.
    
    Models are available with the Pressure Restrictor module option. Note: The R series
    pressure restrictor module is not designed to meet the requirements of a static or drop
    tight pressure reducing valve and has therefore not been verified against these
    requirements by NSF. RPE should be contacted to discuss the requirements for a
    particular application, to ascertain whether the pressure restrictor module is a
    suitable product for the intended use.
    
    Marking: RPE logo and flow arrow on model.
    
    Possible additional markings:
    RPE website and/or max pressure on body.
    Serle R and/or CE on coil housing.
    DOM (wheel type) and www.rpesrl.it on body
[3]  Inlets: ½” BSP (M), ¾” BSP (M) and 8mm push-fit.
    Outlets: 3/8" BSP (M), 1/2" BSP (M), 6.5mm PG hose tail, 8mm PG hose tail,10mm PG hose
    tail,13mm PG hose tail, ¼” spigot, 8mm spigot, 10mm spigot, 6mm push-fit, 8mm push-fit,
    10mm push-fit and 12mm push-fit.
[4] Inlets: ¾” BSP (M).
    Outlets: ¼” BSP (M), 10mm PG hose tail, 13mm PG hose tail, 10mm spigot, 6mm push-fit,
    8mm push-fit and 10mm push-fit.
[5] Inlets: ¾” BSP (M).
    Outlets: 10mm PG hose tail, 13mm PG hose tail, 10mm spigot, 8mm push-fit and 10mm
    push-fit.
[6] Inlets: ¾” BSP (M).
    Outlets: 10mm PG hose tail, 13mm PG hose tail and 10mm spigot.
[7]  Inlets: ¼” BSP (M), 3/8” BSP (M),1/2” BSP (M), ¾” BSP (M), 1/8” BSP (F), ¼” BSP (F),
    3/8” BSP (F), ½” BSP (F), ¾” BSP (F), 10mm PG hose tail, ¼” push-fit, 3/8” push-fit, 6mm
    push-fit, 8mm push-fit, 10mm push-fit and 15mm push-fit.
    Outlets: ½” BSP (M), 3/8” BSP (M), ½” BSP (M), ¾” BSP (M), 1/8” BSP (F), ¼” BSP (F),
    3/8” BSP (F), ½” BSP (F), ¾” BSP (F), 10mm PG hose tail, ¼” push-fit, 3/8” push-fit, 6mm
    push-fit, 8mm push-fit, 10mm push-fit and 15mm push-fit.
[8] Inlets: ¾” BSP (M), ¾” GHT (M), 6.5mm PG hose tail, 10mm PG hose tail and 8mm push-fit.
    Outlets: ¾” BSP (M), 6.5mm PG hose tail, 10mm PG hose tail, 17mm PG hose tail, ¼”
    spigot, 6mm spigot and 10mm spigot.
[9] Inlets: ¾” BSP (M).
    Outlets: 10mm PG hose tail.
[10] Inlets: ½” BSP (M), ¾” BSP (M), ¾” BSP (F), 10mm PG hose tail, ¼” push-fit, 3/8”
     push-fit, 6mm push-fit, 10mm push-fit and garden hose quick connector.
     Outlets: ½” BSP (M), ¾” BSP (M), ¾” BSP (F), 10mm PG hose tail, ¼” push-fit, 3/8”
     push-fit, 6mm push-fit, 10mm push-fit and garden hose quick connector.
[11] Inlets: M10 (M), ¼” push-fit, 6mm push-fit and 8mm push-fit.
     Outlets: ¼” BSP (M), ¼” push-fit, 6mm push-fit and 8mm push-fit.
[12] Maximum operating temperature 60.0°C (All connections excluding push-fit) for cold water
     use only (push fit only connections).