NSF Product and Service Listings

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.

[1] This product is designed to be used off-line following manufacturer’s use instructions.
    The well is to be flushed until the turbidity of the water is < 1 NTU before the system
    may be used for drinking water.
[2] This product can be shipped with either the Cetco® or Volclay® prefix.
[3] This product can be shipped with either the Cetco®, Volclay®, or Puregold® prefix.
[5] The sealant is to be mixed at a ratio of not greater than 18 pounds of product to 50
    pounds of grout.
[6] Certified for use as a well sealant additive only when used in conjunction with a well
    sealant grout.

[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[4] These products are designed to be flushed out prior to using the system for drinking
    water.  Before being placed into service, the well is to be properly flushed according
    to the manufacturer’s use instructions.  Certification of these products is based on the
    well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the 
      drilling fluid has been added at the manufacturer’s recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on 0.5 acre 
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional 
      amount removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.
    

[1] This product is designed to be flushed out until the turbidity of the water is < 1 NTU.
    Flushing is required before the system may be used for drinking water.

[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.

[1] These products are designed to be used off-line and flushed out prior to using the
    system for drinking water, following manufacturer's use instructions.
[2] The well is to be properly flushed and drained until the turbidity of the water is <1
    NTU.

[1] The well is to be properly flushed and drained until the turbidity of the water is <1
    NTU.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. The well is to be properly flushed and drained until the turbidity of the water
    is <1 NTU.
[2] Follow manufacturer's use instructions.
[3] A 5% solution of LBA is to be added to the well in accordance with the dosage table
    (e.g., for a 2" well, a 5% solution is to be added at 0.01 gallon per foot of standing
    water).  The well should then be flushed as outlined in the use instructions.
[WL] These products are designed to be flushed out prior to using the system for drinking

     water.  The well shall be properly flushed and drained before being placed in service.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. The well is to be properly flushed and drained until the turbidity of the water
    is <1 NTU.
[2] This product is designed to be flushed out prior to using the system for drinking water.
    This product must be used according to the manufacturer's use instructions.
[3] The equipment must be disconnected from the system prior to treatment. The well must be
    purged until the pH reaches that of the original water.
[4] The well shall be properly flushed and drained before being placed in service.
[5] A 5% solution of LBA is to be added to the well in accordance with the dosage table
    (e.g., for a 2 inch well, a 5% solution is to be added at 0.01 gallon per foot of
    standing water).

[1] Certified for use as a well sealant additive only when used in conjunction with a well
    sealant grout.  The Sealant is to be mixed at a ratio of not greater than 18 pounds of
    product to 50 pounds of grout.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.
[2] This product is designed to be flushed out prior to using the system for drinking water.
    The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly flushed according to
    the manufacturer's use instructions. Certification of these products is based on the
    well drilling model with the following assumptions: 
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which
      the drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
      aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length
      (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to 
      the combined volumes of the casing and the screen, plus an additional amount removed 
      through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such 
      as cavernous limestone.
[2] This product is designed to be flushed out prior to using the system for drinking water.
    The well is to be properly flushed and drained before being placed into service. This
    product is to be used according to the manufacturer's use instructions.

[1] Certification of this product is based on a well drilling model using assumptions stated
    in NSF/ANSI/CAN 60, Section 8 for well drilling foamers.
[2] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following the manufacturer's use instructions.

[1] This product is designed to be flushed out prior to using the system for drinking water.
    Before being placed into service, the well is to be properly flushed according to the
    manufacturer's use instructions.
[2] Certification of this product is based on the well drilling model with the following
    assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an additional amount removed
    through the well disinfection and development (90% removed).

[1] This product is designed to be used off-line and flushed out prior to using the system
    for drinking water, following manufacturer's use instructions.
[2] This product is designed to be flushed out until the turbidity of the water is < 1 NTU. 
    Flushing is required before the system may be used for drinking
    water.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly
    flushed according to the manufacturer's use instructions. Certification of these
    products is based on the well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an
    additional amount removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.

[1] These products are designed to be flushed out prior to using the system for drinking
    water. Before being placed into service, the well is to be properly
    flushed according to the manufacturer's use instructions. Certification of these
    products is based on the well drilling model with the following assumptions:
    - The amount of well drilling fluid used is 3780 L (1000 U.S. gallons) to which the
    drilling fluid has been added at the manufacturer's recommended level.
    - The aquifer contains 3.1 million liters of water (815,000 gallons) based on a 0.5 acre
    aquifer of 6.1 meter depth (20 ft.) and 25% porosity.
    - The bore hole is 61 meters in total depth (200 ft.), the screen is 6.1 meters in
    length (20 ft.), and the bore hole is 25.4 cm. in diameter (10 in.).
    - The amount of well drilling fluid removed from the well during construction is equal
    to the combined volumes of the casing and the screen, plus an
    additional amount removed through the well disinfection and development (90% removed).
    - This product should not be used in constructing wells in highly porous formations,
    such as cavernous limestone.
[PC] Polyacrylamide Products Certified by NSF International comply with 40 CFR 141.111
     requirements for percent monomer and dose.

[1] The sealant is to be mixed at a ratio of not greater than 58 pounds of product to 50
    pounds of geothermal grout.
[2] Certified for use as a well sealant additive only when used in conjunction with a well
    sealant grout.